Sewage water lifting unit_x000d_
Saniquick BT100 - CH250_x000d_
_x000d_
Use:_x000d_
Pumping of domestic and chemically_x000d_
aggressive sewage water. Salt water_x000d_
(up to 15%) from softening systems and_x000d_
condensate from condensing boilers, as well as_x000d_
clean or dirty water,_x000d_
also with solids._x000d_
_x000d_
Collection tank:_x000d_
Plastic shaft, container volume_x000d_
120.00 l, useful volume 66 l, with 3_x000d_
inlet nozzles DN 100. Nozzle DN 70_x000d_
for venting and cable entry._x000d_
Connection screw and pressure line_x000d_
to the pumps in the container,_x000d_
including a non-return valve._x000d_
_x000d_
Control:_x000d_
Electronic switching device_x000d_
for controlling and monitoring_x000d_
all important operating functions._x000d_
Pneumatic level control with_x000d_
dynamic pressure circuit. Pump change_x000d_
after each switching cycle. Connection_x000d_
of the second pump at peak load. In the event of_x000d_
failure of a pump, automatic_x000d_
Switchover to the reserve pump._x000d_
Overload protection with motor protection relay._x000d_
Optical fault display. Alarm signal through_x000d_
built-in buzzer. Potential-free_x000d_
collective fault message. Configuration via_x000d_
free HOMApp possible. Communication_x000d_
between HOMApp and control via_x000d_
Bluetooth._x000d_
_x000d_
DIN EN 12050-2: TÃœV certified,_x000d_
type tested and monitored._x000d_
_x000d_
Max. temperature of the pumped medium:_x000d_
35°C.
_x000d_
Design:
Installation unit ready for connection
with dirty water collection shaft
as a double lifting unit with
two pumps and control system
_x000d_
Design of pump:_x000d_
Two single-stage_x000d_
submersible drainage pumps._x000d_
Pressure connection 1 1/4 inch (32)._x000d_
Open multi-vane wheel with a_x000d_
free passage of 10.00 mm._x000d_
_x000d_
Mode of operation: intermittent._x000d_
_x000d_
Shaft seal:_x000d_
combination of shaft seal ring_x000d_
and SIC mechanical seal._x000d_
_x000d_
Shaft bearing:_x000d_
Robust, maintenance-free, permanently lubricated_x000d_
roller bearing_x000d_
_x000d_
Motor:_x000d_
Water pressure-tight electric motor,_x000d_
with a 2-pole winding.
Insulation class of the winding B,
protection class IP68. Thermal sensors in the
thermal sensors for temperature monitoring
in the winding
Materials:
Collection container: PE
Extension spindle: plastic PP-GF
Suction sieve: plastic PP-GF
Impeller: plastic PP-GF
Motor housing: highly resistant stainless steel
Outer casing: plastic PP-GF_x000d_
Motor shaft: highly resistant stainless steel_x000d_
Mechanical connecting parts: rustproof stainless steel_x000d_
Elastomers: NBR_x000d_
_x000d_
Technical data:_x000d_
Flow rate Qmax: 12.00 m³/h
Head Hmax: 8.00 m
Number of pumps: 2.00
Power P1: 0.55 kW
Power P2: 0.26 kW
Frequency: 50 Hz_x000d_
voltage: 230 V_x000d_
current type: 1.00 Ph_x000d_
nominal current: 2.50 A_x000d_
speed: 2850.00 1/min_x000d_
Start type: Direct
Tank volume: 120.00 L
Pressure connection: 1 1/4 inch (32)
Weight: 19.92 kg
Explosion-proof: no
Dimensions
Dimensions:
Width: 590.00 mm
Depth: 585.00 mm
Height: 746.00 mm
Connection cable: H07RN-F - 3G1
Length of connection cable: 10.00 m_x000d_
_x000d_
Scope of delivery:_x000d_
Collection shaft with cover, 2 pumps_x000d_
with non-return valve and pipework,_x000d_
10 m connection cable, PCM control unit with_x000d_
pneumatic level control and_x000d_
alarm message._x000d_
_x000d_
Make: HOMA
Shipping weight: |
19,92 kg
|