Saniquick BT100 - CH250 sewage lifting unit

Sewage water lifting unit_x000d_ Saniquick BT100 - CH250_x000d_ _x000d_ Use:_x000d_ Pumping of domestic and chemically_x000d_ aggressive sewage water. Salt water_x000d_ (up to 15%) from softening systems and_x000d_ condensate from condensing boilers, as well as_x000d_ clean or dirty water,_x000d_ also with solids._x000d_ _x000d_ Collection tank:_x000d_ Plastic shaft, container volume_x000d_ 120.00 l, useful volume 66 l, with 3_x000d_ inlet nozzles DN 100. Nozzle DN 70_x000d_ for venting and cable entry._x000d_ Connection screw and pressure line_x000d_ to the pumps in the container,_x000d_ including a non-return valve._x000d_ _x000d_ Control:_x000d_ Electronic switching device_x000d_ for controlling and monitoring_x000d_ all important operating functions._x000d_ Pneumatic level control with_x000d_ dynamic pressure circuit. Pump change_x000d_ after each switching cycle. Connection_x000d_ of the second pump at peak load. In the event of_x000d_ failure of a pump, automatic_x000d_ Switchover to the reserve pump._x000d_ Overload protection with motor protection relay._x000d_ Optical fault display. Alarm signal through_x000d_ built-in buzzer. Potential-free_x000d_ collective fault message. Configuration via_x000d_ free HOMApp possible. Communication_x000d_ between HOMApp and control via_x000d_ Bluetooth._x000d_ _x000d_ DIN EN 12050-2: TÜV certified,_x000d_ type tested and monitored._x000d_ _x000d_ Max. temperature of the pumped medium:_x000d_ 35°C. _x000d_ Design: Installation unit ready for connection with dirty water collection shaft as a double lifting unit with two pumps and control system _x000d_ Design of pump:_x000d_ Two single-stage_x000d_ submersible drainage pumps._x000d_ Pressure connection 1 1/4 inch (32)._x000d_ Open multi-vane wheel with a_x000d_ free passage of 10.00 mm._x000d_ _x000d_ Mode of operation: intermittent._x000d_ _x000d_ Shaft seal:_x000d_ combination of shaft seal ring_x000d_ and SIC mechanical seal._x000d_ _x000d_ Shaft bearing:_x000d_ Robust, maintenance-free, permanently lubricated_x000d_ roller bearing_x000d_ _x000d_ Motor:_x000d_ Water pressure-tight electric motor,_x000d_ with a 2-pole winding. Insulation class of the winding B, protection class IP68. Thermal sensors in the thermal sensors for temperature monitoring in the winding Materials: Collection container: PE Extension spindle: plastic PP-GF Suction sieve: plastic PP-GF Impeller: plastic PP-GF Motor housing: highly resistant stainless steel Outer casing: plastic PP-GF_x000d_ Motor shaft: highly resistant stainless steel_x000d_ Mechanical connecting parts: rustproof stainless steel_x000d_ Elastomers: NBR_x000d_ _x000d_ Technical data:_x000d_ Flow rate Qmax: 12.00 m³/h Head Hmax: 8.00 m Number of pumps: 2.00 Power P1: 0.55 kW Power P2: 0.26 kW Frequency: 50 Hz_x000d_ voltage: 230 V_x000d_ current type: 1.00 Ph_x000d_ nominal current: 2.50 A_x000d_ speed: 2850.00 1/min_x000d_ Start type: Direct Tank volume: 120.00 L Pressure connection: 1 1/4 inch (32) Weight: 19.92 kg Explosion-proof: no Dimensions Dimensions: Width: 590.00 mm Depth: 585.00 mm Height: 746.00 mm Connection cable: H07RN-F - 3G1 Length of connection cable: 10.00 m_x000d_ _x000d_ Scope of delivery:_x000d_ Collection shaft with cover, 2 pumps_x000d_ with non-return valve and pipework,_x000d_ 10 m connection cable, PCM control unit with_x000d_ pneumatic level control and_x000d_ alarm message._x000d_ _x000d_ Make: HOMA