Sanistar 230 D sewage lifting unit

Sewage lifting unit_x000d_ Sanistar 230 D_x000d_ _x000d_ Use:_x000d_ Pumping of sewage and faeces, even_x000d_ with coarse and fibrous components._x000d_ For draining rooms below the backflow level where wastewater is produced, e.g. from toilets, sinks, showers, according to DIN 1986. Collection tank Non-rotting, gas-tight and_x000d_ odor-proof plastic container._x000d_ Inlets: DN 100 horizontal, 180 mm height_x000d_ DN 100 horizontal, 250 mm height_x000d_ DN 100 vertical, DN 40 vertical_x000d_ DN 150 horizontal, DN 150 vertical._x000d_ Pressure connection: flange DN 80 and_x000d_ flexible adapter DN 80/DN 100._x000d_ Soft-seated ball check valve integrated in the pressure connection_x000d_ soft-sealing ball non-return valve integrated in the pressure connection._x000d_ Vent connection: DN 70 vertical._x000d_ Connection for diaphragm hand pump: R 1" female thread._x000d_ Cleaning opening with screw cap._x000d_ _x000d_ Control: Electronic control unit for controlling and monitoring all important operating functions. Pneumatic level control with dynamic pressure switch. Pump change after each switching cycle The second pump is activated at_x000d_ peak load. If a pump fails,_x000d_ automatic switchover to the_x000d_ standby pump. Motor protection with_x000d_ temperature monitoring of the winding._x000d_ Optical fault display. Alarm signal through_x000d_ built-in buzzer. Potential-free_x000d_ collective fault message. Direction of rotation_x000d_ control display. Power plug._x000d_ Can be connected to_x000d_ ServCom diagnostic device (see accessories) for: checking operating hours, switching cycles, maintenance intervals, abnormal operating conditions, changes in switching levels. Easy Retrofitting to a mains-independent alarm_x000d_ by inserting a 9V battery_x000d_ (see accessories)._x000d_ _x000d_ DIN EN 12050-2: TÜV certified,_x000d_ type-tested and monitored._x000d_ _x000d_ Max. temperature of pumping medium:_x000d_ 40°C, briefly up to 60°C._x000d_ _x000d_ Design:_x000d_ Flood-proof single lifting unit_x000d_ with control unit, collection tank and_x000d_ pump ready for connection._x000d_ _x000d_ Design of pump:_x000d_ Pump chamber integrated in the collection tank, vertical pressure connection DN 80._x000d_ Vortex impeller with a free passage of 45.00 mm. Mode of operation: Intermittent operation. Shaft seal triple radial seal. _x000d_ _x000d_ Shaft bearing: robust, maintenance-free, permanently lubricated roller bearing. _x000d_ _x000d_ Motor Water pressure-tight electric motor, with 2-pole winding. Insulation class of winding H, protection class IP68. Materials Pressure cover: gray cast iron EN-GJL-250_x000d_ impeller: gray cast iron EN-GJL-250_x000d_ motor housing: gray cast iron EN-GJL-250_x000d_ collection tank: polyethylene_x000d_ Motor shaft: Stainless steel 1.4104_x000d_ Mechan. connecting parts: Stainless steel_x000d_ O-rings: NBR_x000d_ Shaft seals: NBR_x000d_ Upper bearing: Grooved ball bearing_x000d_ Lower bearing: grooved ball bearing_x000d_ _x000d_ Technical data:_x000d_ Conveying current Qmax: 36.00 m³/h_x000d_ Conveying height Hmax: 15.50 m_x000d_ Number of pumps: 2.00_x000d_ Power P1: 3.00 kW Power P2: 2.10 kW Frequency: 50 Hz Voltage: 400 V Current type: 3.00 Ph Rated current: 5.10 A_x000d_ Speed: 2900.00 1/min_x000d_ Starting method: Direct_x000d_ Tank volume: 95.00 L_x000d_ Pressure connection: DN 80_x000d_ Weight: 111.87 kg Explosion protection: no Cutting mechanism: no Dimensions: Width: 750.00 mm Depth: 750.00 mm_x000d_ Height: 515.00 mm_x000d_ _x000d_ Connection cable: H07RN8-F PLUS - 6G1.5_x000d_ Length of connection cable: 4.00 m_x000d_ _x000d_ Scope of delivery:_x000d_ Container with 2 pumps, soft-sealing_x000d_ Ball non-return valve,_x000d_ pressure connection with flange DN 80 and_x000d_ DN 80/DN 100 elastic adapter_x000d_ with clamps. Elastic_x000d_ connecting pieces for inlet DN 100 and_x000d_ Ventilation DN 70 with clamps._x000d_ Pneumatic level switch._x000d_ Electronic controller_x000d_ Connecting cable with plug._x000d_ _x000d_ Make: HOMA