Sanistar 110 W wastewater lifting system

Sewage lifting unit_x000d_ Sanistar 110 W_x000d_ _x000d_ Use:_x000d_ Pumping of sewage and faeces, also_x000d_ with coarse and fibrous components._x000d_ For draining rooms below the backflow level where wastewater is produced, e.g. from toilets, sinks, showers, according to DIN 1986. Collection tank Non-rotting, gas-tight and_x000d_ odor-proof plastic container._x000d_ Inlets: DN 100 horizontal, 180 mm height_x000d_ DN 100 horizontal, 250 mm height_x000d_ DN 100 vertical, DN 40 vertical_x000d_ DN 150 horizontal, DN 150 vertical._x000d_ Pressure connection: flange DN 80 and_x000d_ flexible adapter DN 80/DN 100._x000d_ Soft-seated ball check valve integrated in the pressure connection_x000d_ soft-sealing ball non-return valve integrated in the pressure connection._x000d_ Vent connection: DN 70 vertical._x000d_ Connection for diaphragm hand pump: R 1" female thread._x000d_ Cleaning opening with screw cap._x000d_ _x000d_ Control: Electronic control unit for controlling and monitoring all important operating functions. Pneumatic level control with dynamic pressure switch. Motor protection with temperature monitoring of the winding. Optical fault display. Alarm signal through built-in buzzer. Potential-free collective fault message. Direction of rotation control display. Mains plug. Connection option for ServCom diagnostic device (see accessories) for: Querying operating hours, switching cycles, maintenance interval, abnormal operating conditions, change in switching levels. Easy Retrofitting to a mains-independent alarm_x000d_ by inserting a 9V battery_x000d_ (see accessories)._x000d_ _x000d_ DIN EN 12050-2: TÜV certified,_x000d_ type-tested and monitored._x000d_ _x000d_ Max. temperature of pumping medium:_x000d_ 40°C, briefly up to 60°C._x000d_ _x000d_ Design:_x000d_ Flood-proof single lifting unit_x000d_ with control unit, collection tank and_x000d_ pump ready for connection._x000d_ _x000d_ Design of pump:_x000d_ Pump chamber integrated in the collection tank,_x000d_ vertical pressure connection 2 inches (50)._x000d_ Vortex impeller with a_x000d_ free passage of 45.00 mm._x000d_ _x000d_ Operating mode: Intermittent._x000d_ _x000d_ Shaft seal:_x000d_ triple radial seal. _x000d_ _x000d_ Shaft bearing: robust, maintenance-free, permanently lubricated roller bearing. _x000d_ _x000d_ Motor Water pressure-tight electric motor, with 2-pole winding. Insulation class of winding H, protection class IP68. Materials Pressure cover: gray cast iron EN-GJL-250_x000d_ impeller: gray cast iron EN-GJL-250_x000d_ motor housing: gray cast iron EN-GJL-250_x000d_ collection tank: polyethylene_x000d_ Motor shaft: Stainless steel 1.4104_x000d_ Mechan. connecting parts: Stainless steel_x000d_ O-rings: NBR_x000d_ Shaft seals: NBR_x000d_ Upper bearing: Grooved ball bearing_x000d_ Lower bearing: grooved ball bearing_x000d_ _x000d_ Technical data:_x000d_ Conveying current Qmax: 44.30 m³/h_x000d_ Conveying height Hmax: 8.00 m_x000d_ Number of pumps: 1.00_x000d_ Power P1: 1.70 kW_x000d_ Power P2: 1.30 kW_x000d_ Frequency: 50 Hz_x000d_ Voltage: 230 V_x000d_ Current type: 1.00 Ph_x000d_ Rated current: 7.10 A_x000d_ Speed: 1450.00 1/min_x000d_ Starting type: Direct_x000d_ Container volume: 70.00 L_x000d_ Pressure connection: 2 inch (50)_x000d_ Weight: 63.05 kg Explosion-proof: no Cutting mechanism: no Dimensions: Width: 550.00 mm Depth: 703.00 mm_x000d_ Height: 453.00 mm_x000d_ _x000d_ Connection cable: H07RN8-F PLUS - 6G1.5_x000d_ Length of connection cable: 4.00 m_x000d_ _x000d_ Scope of delivery:_x000d_ Tank with pump, soft-sealing_x000d_ ball non-return valve,_x000d_ pressure connection with flange DN 80 and_x000d_ DN 80/DN 100 elastic transition piece_x000d_ with clamps. Elastic_x000d_ connecting pieces for inlet DN 100 and_x000d_ venting DN 70 with clamps._x000d_ Pneumatic level switch._x000d_ Electronic control unit Connecting cable with plug. _x000d_ _x000d_ Make: HOMA