Saniboy G 180-16 W sewage lifting unit

Sewage lifting unit_x000d_ Saniboy G 180-16 W_x000d_ _x000d_ Use:_x000d_ Pumping of domestic sewage and_x000d_ faeces. The built-in macerator in front of the impeller_x000d_ Cutting system installed in front of the impeller crushes all cuttable solids so that the pumped liquid can be pumped through pipes from DN 50. For draining rooms below the Backflow level, in which wastewater is produced, e.g. from toilets, sinks, showers, according to DIN 12056. Sump tank Non-rotting, gas- and odor-tight plastic_x000d_ container._x000d_ Inlets: DN 100/40 stepped horizontally_x000d_ at a height of 180 mm._x000d_ DN 100/40 stepped vertically._x000d_ Vent connection: DN 70 vertical. Connection for diaphragm hand pump R 1" IG. Cleaning opening with screw cap. Control: Electronic control unit for controlling and monitoring all important and monitoring of all important_x000d_ operating functions. Pneumatic_x000d_ level control with dynamic pressure switch._x000d_ Motor protection with temperature monitoring_x000d_ of the winding. Optical fault display._x000d_ Alarm signal through built-in buzzer._x000d_ Potential-free collective fault signal. Direction of rotation control display. Mains plug. Connection for ServCom diagnostic unit (see accessories) for: querying operating hours, Switching cycles, maintenance interval,_x000d_ abnormal operating conditions,_x000d_ change of switching levels. Easy_x000d_ retrofitting to mains-independent alarm_x000d_ by inserting 9V battery_x000d_ (see accessories)._x000d_ _x000d_ DIN EN 12050-2: TÜV certified,_x000d_ type-tested and monitored._x000d_ _x000d_ Max. temperature of the pumping medium:_x000d_ 40°C, briefly up to 60°C. Design: Flood-proof single lifting unit with control unit, collection tank and pump, ready for connection _x000d_ Design of pump:_x000d_ Pump chamber integrated in the collection tank, vertical pressure connection 2 inch (50)._x000d_ Open multi-vane wheel_x000d_ with upstream cutter_x000d_ for the maceration of solids with a_x000d_ free passage of 45.00 mm._x000d_ _x000d_ Operating mode: Intermittent._x000d_ _x000d_ Shaft seal:_x000d_ Combination of mechanical seal_x000d_ Combination of mechanical seal_x000d_ (silicon carbide/silicon carbide) and_x000d_ radial seal in oil barrier chamber._x000d_ Oil-filled seal chamber with_x000d_ inspection option through_x000d_ Inspection screw_x000d_ _x000d_ Motor:_x000d_ Water pressure-tight electric motor,_x000d_ with 2-pole winding._x000d_ Insulation class of winding H,_x000d_ protection type IP68._x000d_ _x000d_ Materials:_x000d_ Suction cover: gray cast iron EN-GJL-250_x000d_ Cutting device: stainless steel 1.4122_x000d_ Impeller: gray cast iron EN-GJL-250_x000d_ Pump housing: gray cast iron EN-GJL-250_x000d_ Motor bearing housing: gray cast iron EN-GJL-250_x000d_ Motor housing: gray cast iron EN-GJL-250_x000d_ Collection tank: PE_x000d_ Motor shaft: Stainless steel 1.4104_x000d_ Mechanical connecting parts: Stainless steel_x000d_ O-rings: NBR_x000d_ _x000d_ Technical data:_x000d_ Flow rate Qmax: 18.70 m³/h_x000d_ Delivery head Hmax: 20.40 m_x000d_ Number of pumps: 1.00_x000d_ Power P1: 1.50 kW_x000d_ Power P2: 1.10 kW_x000d_ Frequency: 50 Hz_x000d_ Voltage: 230 V_x000d_ Current type: 1.00 Ph_x000d_ Rated current: 7.50 A_x000d_ Speed: 2900.00 1/min_x000d_ Starting type: Direct_x000d_ Tank capacity: 46.00 L_x000d_ Pressure connection: 2 inch (50)_x000d_ Weight: 48.08 kg_x000d_ Explosion-proof: no_x000d_ Cutting mechanism: yes_x000d_ _x000d_ Dimensions: Width: 550.00 mm Depth: 703.00 mm Height: 453.00 mm Connection cable: H07RN8-F PLUS - 6G1.5_x000d_ length of connection cable: 4.00 m_x000d_ _x000d_ Scope of delivery:_x000d_ Tank with 1 pump, pressure connection with_x000d_ 90° elbow G 1 1/2 female thread. Elastic_x000d_ connecting pieces for inlet DN 100 and_x000d_ venting DN 70 with clamps._x000d_ Pneumatic level switch._x000d_ Electronic control unit_x000d_ Connection cable with plug._x000d_ _x000d_ Make: HOMA