H119 WG EX submersible waste water pump without float

Non-floating waste water pump_x000d_ H119 WG EX_x000d_ _x000d_ Irrigation and drainage tasks in_x000d_ clean or dirty water,_x000d_ including water with abrasive sand or mud content._x000d_ Applications include lowering groundwater levels, keeping construction sites, underpasses or shafts dry, supplying service water, use on ships, emergency response in the event of Flooding, etc._x000d_ _x000d_ Use:_x000d_ Pumping clean or dirty_x000d_ water, including water with abrasive_x000d_ sand or mud_x000d_ _x000d_ DIN EN 12050-2: TÜV certified, type-tested and monitored. Max. temperature of the pumping medium: 40°C, briefly up to 60°C Operating mode: continuous operation (S1)_x000d_ with a max. number of starts of_x000d_ 15 starts/hour with submerged motor_x000d_ designed._x000d_ _x000d_ Type of construction:_x000d_ Single-stage submersible pump for_x000d_ portable and stationary_x000d_ use._x000d_ _x000d_ Hydraulics:_x000d_ Pump housing with horizontal_x000d_ pressure connection 2 inch (50) male thread._x000d_ Open multi-vane wheel with a_x000d_ free passage of 10.00 mm._x000d_ Adjustable gap width between_x000d_ impeller and housing prevents_x000d_ operational power losses._x000d_ _x000d_ Shaft seal: Combination of mechanical seal (silicon carbide/silicon carbide) and radial seal in oil barrier chamber, Oil-filled seal chamber with control option through inspection screw. Shaft bearing: Robust, maintenance-free, permanently lubricated roller bearing _x000d_ Motor:_x000d_ Water pressure-tight electric motor with_x000d_ 2-pole winding._x000d_ Insulation class of the winding H,_x000d_ protection class IP68._x000d_ Thermocouples in the winding_x000d_ for temperature monitoring._x000d_ Monitoring by means of PTC optionally_x000d_ possible._x000d_ _x000d_ Motor cooling:_x000d_ Motor with surface cooling in_x000d_ immersion operation._x000d_ _x000d_ Materials:_x000d_ Suction strainer: gray cast iron EN-GJL-250_x000d_ Suction cover: gray cast iron EN-GJL-250_x000d_ Motor housing: gray cast iron EN-GJL-250_x000d_ Pump casing: gray cast iron EN-GJL-250_x000d_ Impeller: gray cast iron EN-GJL-250_x000d_ Motor shaft: stainless steel 1.4104_x000d_ Screws: stainless steel_x000d_ O-rings: NBR_x000d_ Mechanical seal (medium side): SiC / SiC_x000d_ Shaft seal (motor side): NBR_x000d_ _x000d_ Paint/coating:_x000d_ Two-component paint on_x000d_ Epoxy resin base, RAL 9005. Technical data: Conveying current Qmax: 41.00 m³/h Conveying height Hmax: 16.70 m Power P1: 1.60 kW_x000d_ Power P2: 1.20 kW_x000d_ Frequency: 50 Hz_x000d_ Voltage: 230 V_x000d_ Current type: 1.00 Ph_x000d_ Rated current: 7.10 A_x000d_ Starting type: Direct_x000d_ Pressure connection: 2 inch (50) female thread_x000d_ Weight: 37.92 kg_x000d_ Speed: 2900.00 1/min_x000d_ Explosion-proof: yes_x000d_ _x000d_ Connection cable: H07RN8-F PLUS - 4G1.5_x000d_ Length of connection cable: 15.00 m_x000d_ Pump circuit: without_x000d_ _x000d_ Scope of delivery:_x000d_ Pump with 90 degree connection elbow and_x000d_ STORZ fixed coupling GR. C,_x000d_ Switchgear with motor protection,_x000d_ ON-OFF switch,_x000d_ cable_x000d_ _x000d_ Make: HOMA