Saniquick BT100 sewage lifting unit - TP28M10/2 D

Sewage water lifting unit_x000d_ Saniquick BT100 - TP28M10/2 D_x000d_ _x000d_ Use:_x000d_ Pumping clean or dirty_x000d_ water, also with solids content. For_x000d_ automatic disposal of waste water_x000d_ below the sewer backflow level. For the_x000d_ connection of washbasins and_x000d_ washing machines in cellars and_x000d_ basements._x000d_ _x000d_ Collection tank:_x000d_ Plastic shaft, tank volume 120.00 liters, usable volume 66 liters, with three inlet nozzles DN 100. Nozzle DN 70 for ventilation and cable entry Connection screw and pressure line_x000d_ to the pumps in the container,_x000d_ including a non-return valve._x000d_ _x000d_ Control:_x000d_ Electronic switching device_x000d_ for controlling and monitoring_x000d_ all important operating functions._x000d_ Pneumatic level control with_x000d_ dynamic pressure circuit. Pump change_x000d_ after each switching cycle. Connection_x000d_ of the second pump at peak load. In the event of_x000d_ failure of a pump, automatic_x000d_ Switchover to the reserve pump._x000d_ Overload protection with motor protection relay._x000d_ Optical fault display. Alarm signal through_x000d_ built-in buzzer. Potential-free_x000d_ collective fault message. Configuration via_x000d_ free HOMApp possible. Communication_x000d_ between HOMApp and control via_x000d_ Bluetooth._x000d_ _x000d_ DIN EN 12050-2: TÜV certified,_x000d_ type tested and monitored._x000d_ _x000d_ Max. temperature of the pumped medium:_x000d_ 40°C, briefly up to 60°C. Design: Ready-to-connect installation unit with dirty water collection shaft as a double lifting unit with two pumps and control system_x000d_ _x000d_ Pump design:_x000d_ Two single-stage_x000d_ submersible drainage pumps._x000d_ Pressure connection 1 1/4 inch (32)._x000d_ Open single-vane impeller with a_x000d_ free passage of 10.00 mm._x000d_ _x000d_ Shaft seal:_x000d_ Direction-independent_x000d_ combination of mechanical seal_x000d_ (silicon carbide/silicon carbide) and_x000d_ radial seal in oil barrier chamber._x000d_ _x000d_ Shaft/bearing: Strongly dimensioned_x000d_ chromium steel motor shaft,_x000d_ permanently lubricated roller bearings._x000d_ _x000d_ Motor:_x000d_ Water pressure-tight electric motor,_x000d_ with 2-pole winding._x000d_ Insulation class of winding H,_x000d_ Protection class IP68._x000d_ _x000d_ Motor cooling: jacket cooling of the motor_x000d_ by means of the pumped medium._x000d_ _x000d_ Materials:_x000d_ Collection tank: PE_x000d_ Insertion set: Plastic PP-GF_x000d_ Motor housing: Gray cast iron EN-GJL-250_x000d_ Pump housing: Gray cast iron EN-GJL-250_x000d_ Impeller: Gray cast iron EN-GJL-250_x000d_ Motor shaft: Stainless steel 1.4104_x000d_ Mechanical connecting parts: Stainless steel_x000d_ O-rings: NBR_x000d_ Mechanical seal (medium side): SiC / SiC_x000d_ _x000d_ Technical data:_x000d_ Flow rate Qmax: 22.00 m³/h_x000d_ Head Hmax: 13.60 m_x000d_ Number of pumps: 2.00_x000d_ Power P1: 1.00 kW_x000d_ Power P2: 0.70 kW_x000d_ Frequency: 50 Hz_x000d_ voltage: 400 V_x000d_ current type: 3.00 Ph_x000d_ nominal current: 1.80 A_x000d_ speed: 2900.00 1/min_x000d_ Start type: Direct Tank volume: 120.00 L Pressure connection: 1 1/4 inch (32) Weight: 47.54 kg Explosion-proof: no Dimensions Dimensions: Width: 590.00 mm Depth: 585.00 mm Height: 746.00 mm Connection cable: H07RN-F - 3G1 (WA 4G1.5)_x000d_ length of connection cable: 10.00 m_x000d_ _x000d_ Scope of delivery:_x000d_ Collection shaft with cover, 2 pumps_x000d_ with non-return valves and pipework,_x000d_ 10 m connection cable, PCM control unit with_x000d_ pneumatic level control and_x000d_ alarm message._x000d_ _x000d_ Make: HOMA