Construction pump with agitator head with float HBPR508 WA

Construction pump with agitator head with float_x000d_ HBPR508 WA_x000d_ _x000d_ Use:_x000d_ Pumping clean or dirty_x000d_ water, including water with abrasive_x000d_ Sand or mud._x000d_ Equipped with a stainless steel agitator head_x000d_ to enable a strong pumping effect_x000d_ for muddy and slimy_x000d_ media._x000d_ Areas of application include_x000d_ Cellar drainage, lowering of groundwater levels, drainage of construction sites or shafts, service water supply, use on ships, emergency response in the event of flooding, etc The flooding of the motor ensures_x000d_ adequate cooling even at extremely_x000d_ low water levels. Optimized_x000d_ for professional use on_x000d_ construction sites._x000d_ _x000d_ Max. temperature of the pumped medium:_x000d_ 40°C. _x000D_ Operating mode: continuous operation (S1)_x000D_ _x000D_ Design:_x000D_ Single-stage submersible pump for_x000D_ portable and stationary_x000D_ Use consisting of:_x000d_ _x000d_ Hydraulics:_x000d_ Single-stage centrifugal pump with_x000d_ bottom discharge connection 1 1/2 inch (40) male thread._x000d_ Open multi-vane wheel with a_x000d_ free passage of 6.00 mm._x000d_ _x000d_ Shaft seal:_x000d_ Shaft seal ring in combination_x000d_ with double-acting mechanical seal_x000d_ in oil bath._x000d_ _x000d_ Shaft bearing:_x000d_ Strongly dimensioned chrome steel motor shaft,_x000d_ permanently lubricated roller bearings_x000d_ _x000d_ Motor:_x000d_ Water pressure-tight electric motor_x000d_ with 2-pole winding._x000d_ Insulation class F,_x000d_ protection class IP68._x000d_ Cable connection compartment separate from motor._x000d_ Thermal sensors in the_x000d_ winding for temperature monitoring._x000d_ _x000d_ Motor cooling:_x000d_ Jacket cooling of the motor by means of the_x000d_ pumped liquid._x000d_ _x000d_ Materials:_x000d_ Motor housing: Aluminum_x000d_ Upper motor bearing housing: Aluminum_x000d_ Pressure cover: gray cast iron GJL_x000d_ pump housing: gray cast iron GJL_x000d_ impeller: cast iron GJS_x000d_ suction strainer: PVC_x000d_ motor shaft: stainless steel_x000d_ screws: stainless steel_x000d_ O-rings: NBR_x000d_ Mechanical seal: SiC, ceramic_x000d_ Shaft seal: NBR_x000d_ Upper bearing: grooved ball bearing_x000d_ Lower bearing: grooved ball bearing_x000d_ _x000d_ Technical data: Conveying current Qmax: 17.00 m³/h Conveying height Hmax: 16.00 m Power P1: 1.20 kW Power P2: 0.75 kW Frequency: 50 Hz voltage: 230 V current: 1.00 Ph nominal current: 5.00 A start type: direct Pressure connection: 1 1/2 inch (40) male thread_x000d_ Weight: 16.00 kg_x000d_ Speed: 2850.00 1/min_x000d_ Pump switchover: with internal float switch_x000d_ _x000d_ Connection cable: H07RN8-F - 3G1_x000d_ length of connection cable: 10.00 m_x000d_ pump switchover: with internal float_x000d_ _x000d_ Scope of delivery:_x000d_ Pump with 10.00 m connection cable and STORZ coupling. Connection cable with plug. Make: HOMA